Model No. V09 Angle valve – Brass water shut off valve 1/2″x 1/2″ in Chrome.
Find various angle valves from China Brass Angle Valve Manufacturer Factory. 3 angle valve for kitchen sink faucet and lavatory faucet. Bathroom angle valve, toilet high water pressure angle valve.
Water Shut Off Valve
Model No. V07
Brass Angle Valve for toilet seat, kitchen sink faucet and lavatory faucet. Brass Angle valve Chrome Plated, bathroom angle valve, toilet high water pressure angle valve.
Brass Body Chrome Plated(Cu>57%, Pb<3%);
Brass Cartridge 90 or 180 Degree Open/Close;
Chrome Plated Zinc Angle Valve Handle;
Guarantee: 10 years;
Sanliv Angle valve Package:
1PC (Or A Pair)/Box; 100PCS/Cartons;
Carton Dimension: 35CMx35CMx20CM;
After Service: Top Grade, Satisfied Guarantee.
How to Replace Bathroom Sink Fixtures? Maybe your old faucet drips, or maybe you’re just hoping to create a new look in your bathroom. Follow these steps to install new fixtures without a hassle.
Step 1: Turn the water off
Turn the water off at the shutoff valves and remove the hot and cold supply lines running from the shutoff valves to the faucet. Unscrew the nuts below the faucet using a basin wrench. Remove the old faucet and scrape any old putty or caulk from the basin.
Step 2: Remove drain
Unscrew the nut that connects the drain to the flange using an adjustable wrench if you are replacing the pop-up drain. Then remove the drain flange from the T-connector.
If you can’t unscrew the drain flange from the T-connector, use a reciprocating saw with a metal-cutting blade and cut the drain assembly away just above the T-connector.
Step 3: Check for a gasket
Check your new fixture for a gasket to seal between the faucet and the sink. If the faucet didn’t come with a gasket, liberally spread plumber’s putty on the bottom of the faucet and press it down until putty squeezes out from between the fixture and sink.
Make sure your new faucet fits your sink. Bring the old faucet to the hardware store when you buy the new one and measure them against each other. Make sure that your sink has enough holes to accommodate the new faucet.
Step 4: Tighten the faucet
Tighten the nuts under the faucet with the basin wrench, making sure the faucet is straight and level. Then wrap the inlet pipes with Teflon tape to ensure a watertight seal.
Step 5: Connect supply lines
Connect the supply lines to the inlet pipes on the faucet, wrap Teflon tape around the shutoff valve connections, and connect the other ends of the supply lines to the shutoff valves.
Step 6: Assemble the new drain
Apply pipe joint compound to the new tailpiece and screw it into the T-connector. Then apply a rope of plumber’s putty to the underside of the drain flange and press it into the drain hole.
Step 7: Connect the drain body
Apply pipe joint compound to the drain body and screw it into the drain flange. Then tighten the nut on the drain body, sealing the gasket and washer against the drain flange.
Make sure the branch of the T-connector faces the wall behind the sink.
Step 8: Install the pop-up
Drop the pop-up into the drain with the hole in the back of the pop-up facing the back of the drain. Thread the pivot rod into the T-connector and through the hole in the pop-up. Then hand-tighten the pivot rod’s retaining nut enough that the rod can still move up and down.
Step 9: Install the lift rod
Insert the pop-up’s lift rod through the hole in the top of the faucet and attach the clevis to the rod from beneath the sink. With the pop-up open, insert the lift rod through the nearest hole in the clevis, and then attach the spring clip to the rod on the other side of the clevis.
Step 10: Check for leaks
Unscrew the aerator from the faucet, turn the water on at the shutoff valves, and open the faucet. Let the water run for several minutes, check for leaks, and then reattach the aerator. If there aren’t any leaks, wash up with your new faucet fixture.
Tips about Sanliv Brass Plumbing Angle Valve Installation and how to fix water shut off angle valves to copper tubing, plastic pipes and steel pipe plumbing supplies.
A lavatory/sink requires both hot and cold-water plumbing supply service. The water service plumbing is connected from the rough-in water lines to shutoff valves and from the valves to the hot- and cold-water faucets. When the rough-in plumbing comes out from the wall, use shutoff angle valves. When the rough-in plumbing comes up through the floor, use straight shutoff valves.
Installing shutoff angle valves to steel pipe. Use the following steps to install angle valve on threaded galvanized pipe (see Figure A):
FIGURE A. INSTALLING SHUT OFF ANGLE VALVE, STEEL PIPE
1. Check and clean the threads of the rough-in water pipe.
2. Slide the escutcheon on the pipe, and push it against the finished wall. Coat threads with pipe joint compound.
3. Screw angle valve hand-tight on threads, and then tighten with wrench. Make sure the valve’s other opening is facing up towards the faucets.
4. Set valve in closed position.
Installing toilet shut off valve to rigid copper tubing. Use the following steps to install an angle valve to rigid copper tubing (see Figure B):
FIGURE B. INSTALLING TOILET WATER SHUTOFF ANGLE VALVE, COPPER PIPE
1. Check and clean the copper tubing.
2. Slide the escutcheon, coupling nut, and compression ring onto the tubing.
3. Slide the valve onto the tubing, and screw the coupling nut hand-tight onto the valve. Tighten coupling nut with a wrench. Make sure the valve’s other opening is facing up towards the faucets.
4. Set valve in closed position.
Installing shutoff angle valves to plastic pipe. Use the following steps to install a shutoff angle valve to plastic pipe (see Figure C):
FIGURE C. INSTALLING WATER SHUT OFF VALVE, PLASTIC PIPE
1. Clean and apply primer around the outside end of the rough-in plumbing.
2. Apply solvent cement around the outside end of the rough-in plumbing.
3. Apply solvent around the outside of the smooth end of the male adaptor, and push it onto the end of the rough-in plumbing.
4. Apply pipe joint compound to the shutoff valve threads, and screw valve hand-tight into the female adaptor.
5. Tighten connection using two wrenches: one to hold the adaptor, the other to tighten the angle valve connection. Make sure the valve’s other opening is facing up toward the faucet.
This is the essential tips on installation of a angle stop valve, three angle globe valve, and how to install a crane angle valve.
Model No. V11
Brass Angle Valve, water shut off valve
Sanliv is a reliable Angle valve manufacturer and exporter of brass angle stop valve. find
angle valve fittings, Angle Stop Valve, water shut off valve at sanliv.comAdd a water shut off valve to apartment? Asked by a customer.
“I live in a first-level condominium that used to be an apartment. The entire building is 3 levels. There is one shutoff valve for the entire side of the building that live on. Is there a way to install a shut off valve that only shuts off the water to my unit? I will be needing to turn the water off a few times within the next few months (major remodel) and I don’t want to have to get the association involved every time. Thanks! ”
Installing a water shut off valve or angle valve to your toilet is very easy. Just make the the screw sies of the flexible hose of the faucet and water supply plumbing from the wall.